Yes, if you park your sled in a garage, a shed, or on a trailer, you need a snowmobile stand. A stand holds the back of the sled up so the track hangs free. That keeps the track off a cold floor between rides. It takes the weight off the rear suspension while you’re storing the sled, and it gives you a safe way to warm the track up and set the tension. Polaris tells owners to support the rear on a track stand after every ride, with the track about four inches off the ground. Most riders are covered by a basic track stand or a lever lift. If you do your own clutch and suspension work, a full work stand is worth it. And if the sled has to move around the shop, add sled slides.

Key Takeaways

  • A snowmobile stand lifts the rear so the track hangs free, for storage, warm-ups, and track adjustments.
  • Polaris says to put the sled on a track stand after each ride, with the track about four inches up.
  • A basic track stand or a lever lift covers everyday storage. A work stand lifts the whole sled for real shop work.
  • Sled slides go under the skis and track so one person can move the sled across a smooth floor.
  • Never hold the sled up or stand behind it while the track’s spinning.

What does a snowmobile stand actually do?

It gets the track off the ground. Sounds simple. It is. But it’s doing four jobs at once, and you’ll use all four over a season.

It keeps the track off the floor between rides

Pull a sled into the garage after a ride and the track’s packed with snow and ice. Let it sit on a cold slab overnight and you can come back to a track stuck to the floor. Polaris covers this in its daily storage instructions. At the end of each ride, park on a level surface, support the rear on a track stand, and keep the track about four inches off the ground.

It takes the load off your suspension in storage

A sled sitting on its track all summer is sitting on its rear suspension too. Ski-Doo recommends lifting the track off the ground for storage, and it says that helps maintain the track lug tips. Polaris and Yamaha owner’s manuals say the same thing in different words. Get the back end up before you put it away.

It gives you a safe way to warm up the track

If your sled sat outside overnight, the manuals tell you to warm the track up before you ride. You do that with the rear up on a stand, spinning the track a few revolutions so it loosens. More on doing that safely below.

It lets you set track tension

Every track tension check starts the same way. The track has to hang free. Polaris writes it right into its pre-season checklist. With the track suspended up, off the ground, follow the tension procedure in your owner’s manual. You can’t do that with the track sitting on the floor.

Which kind of stand do I need?

There are four kinds of gear in this category, and they do different jobs. Here’s how they break down.

Basic track stand

This is the simplest stand there is. You lift the back of the sled and set the stand under it. It’s cheap, light, and easy to throw in a trailer. Our Ez-Trac Stand is the basic track stand, and it’s on sale for $23.95 right now, down from $50.95. That’s the cheapest way to keep a track off the floor.

The catch is the lifting. You’re picking up the back of a sled by hand. On a light trail sled, that’s not bad. On a heavy touring or utility sled, you’ll want help or a lever.

Lever lift stand

A lever lift does the lifting for you. Set it under the rear of the sled, pull the handle down, and the lever does the work. Our track stands are built for an easy one-person lift at the right height. The Lever Lift Stand is $107.95. It also keeps track debris off you when you’re servicing the sled, which matters when you’re warming up a track that’s still packed with ice and grit.

If you ride a heavier sled or you ride alone, this is the one I’d buy. It costs more than a basic stand. You’ll stop thinking about it the first time you lift the sled without hurting your back.

Full work stand

A track stand only lifts one end. A work stand lifts the whole sled. The Snowmobile Work Stand is a different class of tool. It’s made in the USA from rectangle tubing, grade 5 hardware, and a baked-on powder coat. It runs on a 5,000-pound jack. It lifts up to 31 inches and collapses to 5 1/2, so it slides under the sled. The lifting pads are 3-inch rubber, and they work on mountain sleds with big holes in the running boards.

At $425.95, it’s not for everyone. But if you do your own clutch work, suspension rebuilds, or carbide and track changes, a sled at working height beats lying on the shop floor. Add the swivel wheel kit for $126.95 and you can roll the stand, sled and all. It’s four non-locking swivel wheels that bolt on.

Sled slides

Sled slides are for moving the sled, not lifting it. A set is three pieces: two for the skis and one for under the track. Set the sled on them and you can push it across a smooth floor and park it exactly where you want it.

We carry two kinds. The plastic sled slides are $48.95, molded from high-density plastic with snap-in swivel casters. The steel sled slides are $82.95, with a powder-coated steel frame, a big non-slip surface, and 2 1/2-inch swivel casters. The steel set fits any ski and carbide setup, including dual runners, tunnel skis, and powder skis.

Slides need a smooth floor. On a cracked or gravel floor, casters don’t roll. They dig in.

How do I use a track stand safely?

A stand is safe when you use it right. But a spinning track hanging in the air is no place to get careless. The warnings in Polaris’s pre-ride warm-up procedure are the ones to follow:

  • Set the sled on a firm, level surface before you lift it.
  • Make sure the stand’s stable under the rear before you start the engine.
  • Stand clear of the front of the machine and the moving track.
  • Never hold the sled up or stand behind it while the track’s turning. A loose track or flying debris can seriously hurt you.
  • Go easy on the throttle. A free-hanging track doesn’t need much.
  • Shut the engine off before you take the sled off the stand.

And lift where your owner’s manual says to lift. Every sled’s a little different at the back end. If you’re not sure where your rear lift point is, check the manual before you hook anything to it.

Which setup makes sense for my garage?

Match the gear to what you actually do with the sled.

  • You ride, park it, and ride again. A track stand is all you need. Get the Ez-Trac if you can lift the back end yourself. Get the Lever Lift if you can’t, or don’t want to.
  • Your garage is tight and the sled has to move. Add sled slides. Steel if your floor is rough or you run unusual skis, plastic if you want to save some money.
  • You haul to a cabin or the trailhead. Throw the Ez-Trac in the trailer. It’s light, and it keeps the track off frozen ground overnight.
  • You do your own wrenching. Get the Work Stand. Add the wheel kit if you’ll move the sled while it’s up.

If you’re only going to buy two things, make it a track stand for everyday parking and a set of slides to get the sled where it needs to go. That pair handles most of what a home garage throws at you.

Snowmobile stands and slides from HitchDoc Outdoors

HitchDoc Outdoors is the powersports side of HitchDoc, a family-owned manufacturer in Jackson, Minnesota. We build Eagle Plows and motorcycle hitches, and we keep a short, practical lineup of snowmobile stands and slides for riders who take care of their own sleds. US ground shipping is free on orders over $100. The Lever Lift clears that on its own.

Doing clutch work this winter too? Our clutch pullers and clutch tools are in the same shop. And if you’re getting the sled ready for the first ride, our pre-season prep guide walks through the rest. Come spring, the off-season storage checklist picks up where this leaves off.

Frequently Asked Questions

How high should my track be off the ground on a stand?

About four inches. That’s what Polaris specifies for daily storage and for warming up the track. You want the track hanging free, not the sled perched high in the air.

Can I leave my snowmobile on a stand all summer?

Yes, and the manufacturers recommend it. Ski-Doo says to lift the track and skis off the ground so the suspension doesn’t sit compressed for months. Polaris and Yamaha storage instructions say to raise the back end too.

Is it safe to run the track while the sled is on a stand?

It’s the standard way to warm up a track, as long as the stand is stable and you stay clear. Keep everyone away from the front of the machine and the track, never stand behind it, and keep the throttle light.

Do I need a stand if I have sled slides?

Probably. Slides move the sled, but the track still sits on the rear slide. A stand is what lifts the track so it hangs free for warm-ups and tension checks.

Will your stands fit my sled?

The steel sled slides fit any ski setup, and the Work Stand’s rubber pads work even on mountain sleds with big running board holes. For the track stands, call (800) 446-8222 with your make and model and we’ll tell you what works.

Ready to get your track off the floor? Shop snowmobile stands and slides, or call us at (800) 446-8222 and we’ll help you pick.